Tuning examples and presets
Please use the supplied defaults until a maiden flight has been conducted and the filtering is confirmed. Once this is done higher gains can be tested. Skipping this step and using these settings without adequate filtering could result in an uncontrollable helicopter.
No filter  | Filters are working  |
⚠ THE CREATORS OF THESE PRE-SETS ASSUME NO RESPONSIBILITY OR LIABILITY FOR DAMAGE CAUSED BY USING THEIR PARAMETERS. IMPROPER USE MAY LEAD TO LOSS OF VEHICLE, INJURY OR DEATH. PROCEED AT YOUR OWN RISK. ⚠
How to use these presets?
There are two options for using these pre-sets.
- Follow the screen shots to configure your helicopter.
- Load from the supplied Diff file. Please note: This method may overwright some of your previously configured settings. Please check and confirm carefully.
Jiawen Bao - M7
- OMPHOBBY M7
- View Pre-set
- Author’s Notes
- Recommended Filters
- I have checked: filters are enabled and working
Author’s Notes - READ BEFORE USING THIS TUNE
Creator: Jiawen Bao @etocii
Rotorflight Version: 2.0.0 Release
Rotorflight Hardware: Flydragon F722 v2.2
Tune Attributes: Precise, Locked-In, 3D, Robotic
This tune has a single profile using the Rotorflight Governor with maximum headspeed of 2200RPM.
Helicopter: OMPHOBBY M7
Main Rotor Blades: RotorTech 715mm Ultimate
Tail Rotor Blades: RotorTech 106mm Ultimate
FBL/Receiver: Flydragon F722v2
Motor: SUNNYSKY R4530
Pinion: 13t
ESC: Hobbywing 260A v5
Dampers: POM
Diff all
Jiawen M7 Diff All - This is suitable for all Rotorflight Controllers
Servos
Mixer: Calibration
Headspeed: 2200RPM
XLPower Nitro Nimbus
Jiawen Bao - Nitro Nimbus.
- Nitro Nimbus
- View Pre-set
- Author’s Notes
- Recommended Filters
- I have checked: filters are enabled and working
Author’s Notes - READ BEFORE USING THIS TUNE
Creator: Jiawen Bao @etocii
Rotorflight Version: 2.0.0 Release
Rotorflight Hardware: Flydragon F722 v2.2
Tune Attributes: Precise, Locked-In, 3D, Robotic
This tune has a single profile using the Rotorflight Governor with maximum headspeed of 2200RPM.
Helicopter: XLPower Nitro Nimbus
Main Rotor Blades: RotorTech 580mm Ultimate
Tail Rotor Blades: RotorTech 96mm Ultimate
FBL/Receiver: Flydragon F722v2
Servos: Theta C1, D1
Engine: OS55HZR
RPM sensor: ALIGN sensor
Diff all
Jiawen Nimbus Diff All - This is suitable for all Rotorflight Controllers
S5 on SBUS Port - Jiawen uses the SBUS port as an extra servo output which is used to control the glow ignighter. This file will configure the extra servo and is suitable for Flydragon F722V2 and NEXUS. It can also be used for the FlywingF405; however, it is output on the DSM port.
Servos
Mixer: Calibration
Headspeed: 2100RPM
With a throttle signal of 100%
XLPower Specter Nitro
Jiawen Bao - Specter Nitro.
- Specter Nitro
- View Pre-set
- Author’s Notes
- Recommended Filters
- I have checked: filters are enabled and working
Author’s Notes - READ BEFORE USING THIS TUNE
Creator: Jiawen Bao @etocii
Rotorflight Version: 2.0.0 Release
Rotorflight Hardware: Flydragon F722 v2.2
Tune Attributes: Precise, Locked-In, 3D, Robotic
This tune has a single profile using the Rotorflight Governor with maximum headspeed of 1950RPM.
Setup:
Helicopter: Specter Nitro
Main Rotor Blades: RotorTech 700mm Ultimate
Tail Rotor Blades: RotorTech 116mm Ultimate
Engine: OS91speed
Pipe: Kenny Ko pipe
Servos: Theta Kenny Ko 12V servos
Throttle Servo: GDW G28-06
FBL/Receiver: Flydragon F722v2
Battery: Gens ACE 3S 2200mah
RPM sensor: XGuard Back Plate Sensor
Glow Ignighter: XGlow Pro ICE igniter
Capacitor: Panasonic 16V 2200μF
Fuel: VP30%
Diff all
Jiawen Nitro Specter Diff All - Jiawen uses the SBUS port as an extra servo output which is used to control the glow ignighter.
Servos
Mixer: Calibration
Headspeed: 1950RPM
With a throttle signal of 85.5%
